Accessories – Orgautomatech https://orgautomatech.fr Midi interfaces for mechanical musical instrument and more... Mon, 23 Feb 2026 15:57:02 +0000 en-US hourly 1 https://wordpress.org/?v=6.9.4 https://orgautomatech.fr/wp-content/uploads/2020/09/cropped-Poitevin-carre2-32x32.png Accessories – Orgautomatech https://orgautomatech.fr 32 32 2 Go SD card https://orgautomatech.fr/produit/128-mo-sd-card/ Tue, 29 Sep 2020 09:07:28 +0000 https://orgautomatech.fr/?post_type=product&p=991 128 Mb Sd card]]>

2 Go Sd card

Ready for Midilector

Capacity: around 3500 multi channel midi files (average size).

Comes with midifile 0 examples.

]]> Midi 32 Assistant https://orgautomatech.fr/produit/midi-32-assistant/ Fri, 18 Sep 2020 09:21:50 +0000 https://orgautomatech.fr/?post_type=product&p=739 The module board “Midi Assistant 32” is designed to be plugged to an Orgautomatech Midi2Org_32 board, version 3.5 and later.

This module allows you to drive  the Midi decoder 32-output board,   especially to check  all coils connected to the outputs,  to facilitate the tuning of pipes, test pneumatic valves, etc …

You can install it permanently on your organ at your fingertips, it will be useful very often.

  • Check outputs one by one (without going through the Midi)
  • Keep your hands free to tune your pipes  quietly.
  • Check the speed of your pneumatic relay valves with the “repeat mode”.
  • Quick check of all notes at any time with the “sequence” mode.

Instructions manual:Midi assistant 32

]]> ULN2803A https://orgautomatech.fr/produit/uln2803a/ Wed, 16 Sep 2020 13:05:46 +0000 https://orgautomatech.fr/?post_type=product&p=618

ULN2803A ST – Eight darlington arrays

  • 8 output
  • 500 mA max each output
  • 2 Amp max for 8 outputs
  • Output voltage up to 50 volts
  • For Orgautomatech midi decoder boards 16, 32 or 64

Technical datas: ULN2803A_ST_electronics

]]> SecuryFuse https://orgautomatech.fr/produit/securyfuse/ Wed, 16 Sep 2020 12:33:40 +0000 https://orgautomatech.fr/?post_type=product&p=606 A board with 8 input/output, each protected by a fuse. In case of problem (short or something else) with a solenoid, the midi board is safe.

standard fuse 5*20.
Comes with 8 * 500mA fuses.
88 mm long, 50 mm wide.
Can be used to protect 8 groupes of solenoids. In that case, choose correct value for fuses.

]]> Midi cable https://orgautomatech.fr/produit/midi-cable/ Mon, 14 Sep 2020 09:52:41 +0000 https://orgautomatech.fr/?post_type=product&p=515 Standard Midi DIN cable,  5 pins, male/male

lenght 1.50 meter (5 Ft), 2 meter (6.5ft) or 5 meter (16 Ft)

Useful for linking any midi device or midi boards

]]> Midistributor X4 https://orgautomatech.fr/produit/midistributor-x4/ Fri, 11 Sep 2020 09:29:57 +0000 https://orgautomatech.fr/?post_type=product&p=425 Midithru board, 1 input 4 Output.

To “distribute” the Midi flow to up to 4 boards, allowing them to receive data without latency.

Available in 3 versions:

  • Complete : with all cables to connect to other boards. Midi wire and socket + power line cable.
  • Minimum: the components are already soldered on board,  you just will need to solder your cables on the board to connect other midi devices, you can then, adapt the wire lenght to your need.
  • Standard:  Board itself with connectors already soldered, no Midi wire and socket

This product is no longer available.

]]> 16-way flat ribbon https://orgautomatech.fr/produit/16-way-connector-flat-ribbon/ Wed, 09 Sep 2020 13:04:47 +0000 https://orgautomatech.fr/?post_type=product&p=378 Flat ribbon to use with 16-pin connector, to wire onto the K2M 64 and 32 midi encoder boards

]]> Flat cable, sold by whole meter.
Useful to wire your keyboard contacts to midi encoder board input.
To use with 16-pin HE10F connectors.

3M, PVC, 28AWG, 1.27 pitch

Technical datas: 3M-datasheet-flat cable

]]> 16-way connector https://orgautomatech.fr/produit/16-way-connector/ Wed, 09 Sep 2020 12:28:05 +0000 https://orgautomatech.fr/?post_type=product&p=371 HE10F16 connector, female 2*8 cts for ribbon cable to use with Orgautomatech Midi encoder boards, K2M32, 48 and 64.

]]> 16 contact connector, 2.54 pitch, to use with flat ribbon.
Use it to wire the midi board K2M 32 & 64 inputs
You need 4 of them for K2M 32, 6 for K2M48 and 8 for K2M64
Don’t forget to order the  needed lenght of ribbon cable.
Use a small wise to mount the connector on the ribbon (gently please). Then, you can solder -or attach using terminal blocks- the other ends of each of the 16 wires to your keyboard contacts.

16-contact connector, flat ribbon

16-contact connector, 2.56 pitch to use with flat ribbon.

]]>